The battery has only 3V. Is this normal or should the UPS beeps instead? APC ES is making a squealing noise and when you try to reset it the green light blinks and the squealing noise comes back.
I just replaced the battery on my CS but it has 2 beeps and followed by another 2 beeps. What is the problem? What does this mean? How do I fix this? My back up stabilizer when I press the power button beeps all the time only red light blinks a all the time. The green light doesn't come on. What is the service life for the unit if it takes a several surges per year? How can I tell when its time to replace?
Does the surge protection wear out? Do you think it is the unit? What does this indicate? Press the push-button on the front panel of the BackUPS. To install the software, perform the following steps: 1. Follow the installation instructions on the computer screen. Mac OS 9 9. All Other Users The software is designed for the Windows and Macintosh operating systems mentioned in this section.
To replace the internal battery, proceed as follows: Note: Replacing the battery is a safe procedure. Slide the battery Pull the battery out, exposing the battery terminals compartment cover upward and off of the UPS. Align the battery compartment cover with the grooves Connect the battery wires to the terminals as follows: in the UPS. Disconnect non-essential equipment from the Back-UPS. Reset the circuit breaker located on the rear panel of the Back-UPS by push- ing the circuit breaker button fully inward until it catches.
If the circuit breaker resets, switch the Back-UPS on and reconnect the equipment one-at-a-time. If the circuit breaker trips again, it is likely that one of the connected devices is causing the overload. Very low or no utility voltage. Check the wall outlet that supplies power to the Back-UPS using a table lamp. If the lamp bulb is very dim, have the utility voltage checked by a qualified electrician. Check the battery connections. Surge Only outlet. The wall outlet that the Back-UPS is Connect the Back-UPS to another wall outlet or have a qualified connected to does not supply utility electrician check the building wiring.
Unplug non-essential Battery Backup connected equipment, such as printers and plug them into Surge Only outlets. Note: Devices that have motors or dimmer switches laser printers, heaters, fans, lamps, and vacuum cleaners, for example should not be connected to the Battery Backup outlets. Back-UPS battery is weak due to Charge the battery. The battery charges whenever the Back-UPS is recent outage and has not had time connected to a wall outlet. Typically, eight hours of charging time are to recharge.
Back-UPS run-time is reduced until the battery is fully charged. Battery requires replacement. Replace battery see Order Replacement Battery.
Batteries typically last years, shorter if subjected to frequent power outages or ele- vated temperatures. A red indicator is lit Battery is not connected properly. Consult 'Connect the Battery' under 'Installation' on the front page of this document. It shows how to access the battery and connect the wires. The Overload indicator is lit if Move one or more equipment power plugs to the Surge Only outlets.
The battery should be replaced within two weeks see 'Order Replacement Battery'. Failure to replace the battery will result in reduced run-time during a power outage. Red indicators are flashing Back-UPS failure. Call APC for service. Order Replacement Battery The typical battery lifetime is years depending on the number of discharge cycles and operating temperature.
Transfer Voltage Adjustment optional In situations where the Back-UPS or connected equipment appears too sensitive to input voltage, it may be necessary to adjust the transfer voltage. To adjust the transfer voltage, proceed as follows: 1. Plug the Back-UPS into the utility power source. Once in Programming Mode, if the pushbutton is not pressed within 5 seconds, the Back-UPS will exit the Programming Mode, and all indicators will extinguish. The following steps should be taken: 1. Consult the Troubleshooting section to eliminate common problems.
Write the RMA on the outside of the package. Hot-swappable batteries Ensures clean, uninterrupted power to protected equipment while batteries are being replaced Resettable circuit breakers Enables quick recovery from UPS overload events. Transformer-block spaced outlets Protect equipment with input transformer blocks without blocking access to other receptacles. User-replaceable batteries Increases availability by allowing a trained user to perform upgrades and replacements of the batteries reducing Mean Time to Repair MTTR.
Please Note: Extended Warranties must be purchased before the termination date of the original factory warranty, Extended Warranties are non transferable. Some aspects of the service definition presented on this web site may vary by location.
In the case of a conflict between the service definitions contained on this site and the local service definitions the local service definitions will prevail. For more information, please visit our services page. Service Pack 1 Year Extended Warranty for concurrent sales.
0コメント