Finally, click Next to start extracting BIN files. A virtual drive software can mount disc image files as virtual disc drives for different usage. Step 2. Change "filename.
Save the text document, rename the. I hope that after reading this tutorial, you can find your favorite. In addition, if you have a better recommendation, please feel free to contact us, we will continue to update the best content. If this article really helps you, please share it with more people. A wonderful ISO extractor below you may like, free download it here! Try it out!
Header I got them, but i don't know waht to do. Connect the serial cable to the receiver and Comm 1 or Comm 2 port of your computer. Double check and make sure the cable is securely connected.
Plug in the receiver power core, make sure the switch is turn to "ON " from the rear panel, Then turn the power ON with remote control or from the front. You have to wait for receiver to boot up and indicated ON. Click the Download button, wait until the Download Completed. NOw You can turn off power, then disconnect it from the PC. A solder tab is not soldered with out the part in this style of manufacture, therefore I believe that the part was accidentally omitted.
At the time of release, it wouldn't make any difference. The new MX has the modifications necessary to prevent the problem. Now the good news is that the receiver isn't dead Its just sleeping and locked in a loop. Follow these steps and you can use it again. The Receiver has to be modified and woken up. None of this is hard if you follow these steps exactly.
To modify the receiver we will add 1 resister and we will add header pins to connect the JTAG cable. We then have to wake up the CPU by resetting it. We then have to clear the original flash on the receiver. Then we have to apply the original flash.
Your receiver will work at this point. Then we apply the auto roll flash by serial interface. The easiest was to make the cable is to take a serial pass through cable and cut it about 3 feet from the male connector end. Take a meter and starting from pin 1 on the male DB25 organize the wires on the other end. You need the wires from pin 2,3,4,5,13,18,19,20,21,22,23,24, You can cut the rest. Twist wires 18 to 25 together as ground. The rest of the wires are your data lines.
Place the 4 LED's on the board and organize them in such a way that you can add the other components. Bend the leads so the parts won't fall out but don't solder them yet. Measure the distance with the LED's and drill 4 holes in the plastic box that will line up to the position of the LED's on the perf board. Continually check as you go as its hard to fix a miss drilled hole.
Also make sure that you can place the board inside the box and put the lid on. When your satisfied that the parts are in the right spot, Push the leds into their appropriate holes in the case. The board should now be in a position to solder the parts into their final position. Cut the excess wires off and clean up the board. Make a test with your meter and confirm continuity with no shorts. Now attach the DB25 wires to the appropriate spot as well as the flat ribbon 10 pin connector.
The cathode of the LED to the anode of the 1N This is repeated for DB25 Pin 3,4,5. The cathode of the 1N goes to ground. Please note that in the diagram above, it looks like the wires are connected in order. I did this for simplification. Refer to the reference chart above to make sure. I have read about the buffered JTAG cable and I built one and found no difference in process or effectiveness.
I think cheaper is always better. Remove the case screws and remove the top panel of the case. Make sure the unit is unplugged, remove the power connector plug from the receiver board. Unplug the gray cable from the center socket near the CPU. Unscrew the screws holding the board to the case. Remove the coax cable connector rings. Don't forget the rear panel screw near the RCA plugs. Gently remove the receiver board from the case. Remember to ground yourself before touching the board.
Static discharge will damage it. Locate the following tabs on your receiver If your machine is a MX go here. There are holes under these tabs filled with solder and this must be removed. Take the tip of your soldering iron and hold it on the tab for about 6 sec then with your other hand spray air through the hole to blow out the solder. The air will quickly cool the board and help minimize trace burning. You can figure out with your iron exactly how long it takes to melt the solder but try and not take too long.
The traces will lift and or melt if heated too much. Do not attempt to drill new holes. Do not use a soldering gun.. Do not use a cool heat soldering iron. Take the 10 pin header and cut it into 2 - 5 pin header strips. Put the header strips through the holes on the board and re solder the pins on the underside of the board. The modification to the receiver is easy if you take these steps exactly.
I have seen and read alot of crazy mod suggestions but trust me this is not that hard. Don't scrape traces and don't attempt to solder to the cpu. Parts you will need:. Study the picture below and familiarize your self with your receiver.
Visualize where you have to put the resister using the photo below. The 5 resister bank shown below will be missing the 4th resister. The solder tabs on the board are already tinned and ready for the mod. Put a very small amount of solder on the ends of the wire.
No big balls of solder are allowed. Just tin it.
0コメント